รายละเอียดย่อ :
ดิจิตอลมิกเซอร์ Digital Mixing Console 32 Analog input, 16 output, 8 Matrix.( Max 64 input via optional i/o ), Superior Dante Networking Built In.Fader configuration: 32 + 2 (Master), Stainless steel iPad support stays.
รายละเอียดทั้งหมด :
YAMAHA QL5 ดิจิตอลมิกเซอร์ Digital Mixing Console 32 Analog input, 16 output, 8 Matrix.(
Max 64 input via optional i/o ), Superior Dante Networking Built In.Fader configuration:
32 + 2 (Master), Stainless steel iPad support stays.
- Mix channels: 64 mono, 8 stereo.
- Busses: 16 mix, 8 matrix (Input to Matrix supported).
- Local I/O: 32 in, 16 out.
- Fader configuration: 32 + 2 (Master).
- Stainless steel iPad support stays.
specifications
| Sampling frequency rate |
Internal |
44.1kHz / 48kHz |
| External |
44.1kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm), 48kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm) |
| Signal delay |
Less than 2.5ms, INPUT to OMNI OUT, Fs= 48kHz |
| Fader |
100mm motorized, Resolution=1024steps, +10dB to –138dB, –∞dB all faders |
| Total harmonic distortion |
Less than 0.05% 20Hz-20kHz@+4dBu into 600Ω, INPUT to OMNI OUT, Input Gain= Min. |
| Frequency response |
+0.5, -1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, INPUT to OMNI OUT |
| Dynamic range |
112dB typ.: DA Converter / 108dB typ.: INPUT to OMNI OUT, Input Gain = Min. |
| Hum & noise level |
Equivalent input noise |
-128dBu typ., Equivalent Input Noise, Input Gain=Max |
| Residual output noise |
-88dBu, Residual output noise, ST master off |
| Crosstalk |
-100dB*1, adjacent INPUT/OMNI OUT channels, Input Gain = Min. |
| Power requirements |
100-240V 50/60Hz |
| Power consumption |
200W |
| Dimensions |
W |
828mm(32.6in) |
| H |
272mm(10.7in) |
| D |
563mm(22.2in) |
| Net weight |
21.8kg(48.1lb) |
| Accessories |
Owner’s Manual, dust cover, power cord, DVS license sheet |
| Options |
Mini-YGDAI cards *2 , Gooseneck Lamp LA1L, Nuendo Live |
| Others |
Operating temperature range: 0 - 40℃, Storage temperature range: -20 - 60℃ |
Crosstalk@1kHz : A 22kHz, 30dB/Oct filter is used to measure crosstalk.
Total Harmonic Distortion : An 80kHz, 18dB/Oct filter is used to measure total harmonic distortion.
Hum & Noise : An A-Weight filter is used to measure hum &noise.
Analog input characteristics
| Input Connectors |
GAIN |
Input
Impedance |
Source
Impedance |
Input level |
Connector |
| Sensitivity*¹ |
Nominal |
Max. before clip |
INPUT
1-32 *6 |
+66dB |
7.5 kΩ |
50-600 Ω
Mics &
600 ΩLines |
–82dBu
(61.6μV) |
–62dBu
(0.616mV) |
–42dBu
(6.16mV) |
XLR-3-31
type
(Balanced) *2 |
| –6dB |
–10dBu
(245mV) |
+10dBu
(2.45V) |
+30dBu
(24.5V) |
*1. The sensitivity is the input level required for output at +4dBu (1.23V) or at the defined level when all the faders and level
controllers are set to the maximum value.
*2. XLR-3-31 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*3. 0dBu=0.775 Vms for all specifications.
*4. All the AD converters use 24-bit linear/128-times oversampling.
*5. The INPUT connectors have +48V DC (phantom power) jacks, each of which can be turned on/off individually from the console software.
*6. QL1: INPUT1-16
Analog output characteristics
Output
Connectors |
Output
Impedance |
Load
Impedance |
Maximum
Output
Level *5 |
Output Level |
Connector |
| Defined Level |
Maximum
Non-Clip Level |
OMNI
OUT 1-16 *7 |
75 Ω |
600 Ω
Lines |
+24dB
(default) |
+4dBu
(1.23V) |
vt+24dBu
(12.3V) |
XLR-3-32 type
(Balanced) *1 |
| +18dB |
–2dBu
(616mV) |
+18dBu
(6.16V) |
| PHONES |
15 Ω |
8 Ω
Phones |
- |
75mW *6 |
150mW |
Stereo Phone
Jack(TRS)
(Unbalanced) *2 |
40 Ω
Phones |
- |
65mW *6 |
150mW |
*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*2. The PHONES connectors for stereo headphones are balanced jacks (Tip=LEFT, Ring=RIGHT, Sleeve= GND).
*3. 0 dBu=0.775 Vms for all specifications.
*4. All the DA converters use 24-bit linear/128-times oversampling.
*5. The console has an internal switch for toggling the maximum output level.
*6. This is a value measured with the PHONES LEVEL knob set to 10 dB below the maximum position.
*7. QL1: OMNI OUT 1-8
Digital input/output specifications
| Connectors |
Format |
Data length |
Level |
Audio |
Connector |
| Primary/Secondary |
Dante |
24bit or 32bit |
1000Base-T |
64ch Input/64ch
Output@48kHz *1 |
EtherCON Cat5e |
*1. QL1: 32ch Input/32ch Output@48kHz
Digital output specifications
| Connectors |
Format |
Data length |
Level |
Connector |
| DIGITAL OUT |
AES/EBU |
AES/EBU Professional Use |
24bit |
RS422 |
XLR-3-32 type (Balanced) *1 |
*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
I/O SLOT (1-2) specifications
Each I/O Slot accepts a Mini-YGDAI card.
Only Slot 1 has a serial interfac
Control I/O characteristics
| Connectors |
Format |
Level |
Connector |
| MIDI |
IN |
MIDI |
- |
DIN Connector 5P |
| OUT |
MIDI |
- |
DIN Connector 5P |
| WORDCLOCK |
IN |
- |
TTL/75 Ω terminated |
BNC Connector |
| OUT |
- |
TTL/75 Ω |
BNC Connector |
| GPI (5IN/5OUT) |
- |
- |
D Sub Connector 15P(Female) *1 |
| NETWORK |
IEEE802.3 |
10BASE-T/100Base-TX |
RJ-45 |
| LAMP (QL5: x 2, QL1: x 1) |
- |
0V-12V |
XLR-4-31 type *2 |
| USB HOST |
USB 2.0 |
- |
USB A Connector (Female) |
|
